Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterClopay Torsion Spring Replacement: The Manor Owner’s Guide
We stock and install Clopay-compatible torsion spring replacements for most residential models in Manor, with typical installed pricing at $180-$340 and same-day service when you call early. Most Clopay doors in this area use either a 2-inch or 1-3/4-inch diameter spring system, and we carry both on the truck. You’ll know the spring has failed when the door feels suddenly heavy, won’t stay open halfway, or you heard a loud bang from the garage yesterday and now the opener strains but barely moves.
Which Clopay Models This Applies To
Clopay has used several torsion spring configurations across their lines, and getting the match right matters more than with some other brands. The Classic Collection and Gallery Series steel doors from roughly 2002 onward typically run 2-inch springs with 0.225 to 0.250 wire gauge, while the Coachman Collection and some Reserve Wood doors use the 1-3/4-inch EZ-Set torsion system. The Avante and Modern Steel lines have their own spec ranges.
To identify what you have, look for the Clopay sticker on the interior top section of the door. It lists the model number, serial, and often the original spring specs. If the sticker’s faded, we measure wire diameter, inside diameter, and overall length on-site. We match OEM spec or use an equivalent from a quality aftermarket source. The aftermarket springs we carry meet the same cycle-life ratings, and we warranty them the same way. We’re an independent service provider, not affiliated with Clopay.
One compatibility gotcha in Manor: some Clopay doors installed during the 2015-2018 building boom out past Shadowglen were fitted with non-standard 2-5/8-inch inside diameter springs that aren’t stocked by most suppliers. We carry those too.
Signs Your Clopay Torsion Spring Replacement Is Failing
- The door slams shut or won’t stay at half-mast. A torsion spring’s job is counterbalance. When it loses tension, the full weight of a 150- to 250-pound Clopay steel door drops onto the opener and your back. This is the most common call we get from neighborhoods off Parsons Road.
- You heard a single loud crack from the garage, then silence. That’s a torsion spring snapping under load. Clopay springs are wound to roughly 10,000-15,000 cycles, and in Manor’s heat, the metal fatigues faster than in cooler climates. A cycle is one open and close.
- The opener motor runs but the door barely budges. The opener isn’t designed to lift the door’s full weight. It’s only meant to guide a balanced door. When the spring fails, the motor overheats and strains against a load it was never meant to carry.
- Visible gap in the spring coil. A healthy torsion spring has tight, even coils. A gap of even an inch means the spring has broken internally and is no longer doing its job. Don’t try to close that gap yourself.
- The door opens crooked or one side lags. Clopay doors with a dual-spring setup can fail on one side first. The door lifts unevenly, stressing the cables and tracks. Catching this early saves the cables, which run $130-$250 if they go too.
Replacement Cost & What’s Included
| Service | Price Range in Manor |
|---|---|
| Single torsion spring replacement | $180-$260 |
| Dual spring replacement (both springs) | $280-$340 |
| Spring + cable replacement (if cables are worn) | $310-$490 |
What drives the range: door height (7-foot vs. 8-foot), spring diameter and wire gauge, whether we’re matching one spring or replacing a pair, and if the cables or bearing plates need attention too. We state the flat price before any work starts. No surprises on the bill. The price includes the spring, labor, winding bars, safety cables if code requires them, and a written 90-Day Done Right Promise. If it’s not right, we come back. No paperwork, no arguing.
DIY or Call Us?
There’s a safe middle ground here. You can check the door’s balance by pulling the red release handle and lifting manually. If it won’t stay at waist height, the spring is suspect. You can also look for the gap in the coils or listen for the opener straining. That’s as far as we’d recommend going.
Torsion springs store massive kinetic energy. Winding or unwinding them without proper bars and training risks serious injury. We’ve seen bent winding bars, broken wrists, and worse. The tools aren’t expensive, but the mistake is. Carl Dutton’s been formalizing this trade since Los Angeles Trade-Technical College, and even with decades on the job, he treats every spring with respect. Quote first, wrench second. If your Clopay door needs a torsion spring in Manor, call (737) 214-0959. We’ll answer live, quote upfront, and most days we’re there within hours.
FAQs
Most standard-cycle springs last 7-10 years in this climate, though Manor’s heat and humidity accelerate metal fatigue. A spring rated for 10,000 cycles, used four times daily, gives roughly seven years. High-cycle springs can double that. Call (737) 214-0959 and we’ll tell you what’s on your door.
No. Once a torsion spring breaks or loses tension, replacement is the only safe fix. Rewinding a fatigued spring is temporary and dangerous. We replace with new, properly specced springs and warranty the work for 90 days.
Most Clopay torsion spring replacements take 45 minutes to an hour on site. We carry the common sizes for Clopay models on every truck, so there’s no ordering parts or second trip. You’ll get a call window and we’ll be there when we say.
Yes. We stock springs for Clopay’s 2-inch and 1-3/4-inch systems, including the less common 2-5/8-inch inside diameter used on some Manor installations. We also stock LiftMaster, Chamberlain, and Genie opener parts, plus cables and rollers, so most jobs finish in a single visit.
Written by Carl Dutton, Owner, Mainspring Garage Door Co. at Mainspring Garage Door Co., serving Manor and nearby areas.